1. Step 1: Vehicle Overview.
2. Step 2: Check Engine Compartment.
3. Step 3: Start Engine and Inspect Inside the Cab.
4. Step 4: Turn Off Engine and Check Lights. ...
5. Step 5: Do Walkaround Inspection. ...
6. Step 6: Check Signal Lights.
7. Step 7: Start the Engine and Check.

What is the seven step inspection procedure?

1. Vehicle Overview.
2. Check engine compartment.
3. Start engine and inspect cab.
4. Turn off engine and check lights.
5. Do walkaround inspection.
6. check signal lights.
7. start engine and check.

What are the steps for a pre-trip inspection?

1. Check for problems under the hood.
2. Ensure the truck is not leaning.
3. Make sure the cabin is safe.
4. Check that the brakes are working properly.
5. Look for flaws in the coupling system.
6. Look for defects in the trailer.

How do you memorize a CDL pre-trip inspection?

The only way to memorize the pre-trip is to repeat it over and over. Start with the engine area and work your way around the truck and finally inside the cab. There is no way around consistent repetition. The more you do it the more you will memorize it.

What are the ABC for pre-trip inspection?

Air gauges (primary Page 3 PRE-TRIP INSPECTION STUDY GUIDE ABC– Abrasions, Bruises, Cuts (plastic, rubber) -- BBC Bent, Broken, Cracked (metal) -- No Leaks (air, liquid) Wear gloves and touch every part you inspect. Inspect from the top down and center out. and secondary gauge)- Operational, rising to or at proper ...

CDL CLASS A Pre-Trip Inspection 2020 (Updated) - Driving Academy How to Pass CDL Your Road Test

What sort of things should you inspect during a trip?

• Watch gauges for signs of trouble.
• Use your senses to check for problems (look, listen, smell, feel).
• Check critical items when you stop: Tires, wheels and rims. Brakes. Lights and reflectors. Brake and electrical connections to trailer. Trailer coupling devices.

What is normal to find in a pre trip inspection?

What You Need to Know About The Pre-Trip Inspection. ... You will have to do thorough safety inspections of the coupling system, the vehicle lights, engine compartment, tires and brakes, the chassis, the fuel tanks, and an in-cab inspection.

Which state has the hardest driving test?

KOMO News recently reported on a study by Siegfried and Jensen, which says that Washington state is the hardest state in the nation to pass the driving test.

What are the 3 types of vehicle inspections?

• Pre-Trip Inspections. Under §392.7 of the Federal Motor Carrier Safety Regulations (FMCSRs), the driver must be satisfied that the vehicle is in “good working order” before operating it. ...
• En-Route Inspections. ...
• Post-Trip Inspections. ...
• Bottom Line.

What is a courtesy inspection?

The Courtesy Inspection is a “visual” inspection and takes a few minutes to perform. The technician will look for obvious problems such as tires that look low in air, leaks, frayed wiper blades, corroded battery terminals, a dirty air filter and a few more items. ... This is a very thorough inspection.

What is a post-trip inspection?

What Is a Post-Trip Inspection? Also referred to as a Driver Vehicle Inspection Report (DVIR), a post-trip inspection documents vehicle fault conditions known to the driver at the conclusion of each trip. It occurs at least once every 24 hours if a trip extends beyond a day.

What is a digital vehicle inspection?

Let's Summarize what is Digital Vehicle Inspection

DVI is software where the vehicle inspections are recorded electronically. DVI replaces the traditional method of using paper inspection sheets, clipboards with smartphones or tablets.

How many steps are in pre-trip?

Quia - Review the seven-step pre-trip inspection.

Do you fail for hitting the curb?

Many learners assume that hitting the kerb while performing a manoeuvre will result in an instant fail, but again it's not entirely true. While mounting the kerb – or crashing into it hard – will be marked down as a major, a simple touch or clip during a manoeuvre (like turning in the road) is only classed as a minor.

What is a three point turn?

What is a Three-Point Turn? The three-point turn is a way of turning a vehicle around in a small space by going forward, turning to one side, then backing up, turning in order to face the other direction, then going forward again. This type of turn is usually done when the road is too narrow for a U-turn.

What is the lowest passing score you can get to pass your driving skills test?

In most states, you need a score of 80 percent to pass. 32 states have a passing score of 80 percent. Most of these states have 25 questions on the test, which means you must correctly answer 20 questions to pass the exam.

How often should a pre trip inspection be completed?

A pre-trip inspection is required before the start of each driving shift and once over the course of every 24 hours while on the road. Before heading out on the road, drivers are required by law to inspect their truck and trailer for possible mechanical issues and safety concerns.

What is the 11 hour limit?

2. What is the 11-hour rule? The 11-hour rule states that within the 14-hour window, a property-carrying driver can drive a maximum of 11 hours after 10 consecutive hours off duty. Passenger-carrying drivers can drive up to 10 hours after eight consecutive hours off duty.

Why put the starter switch key in your pocket during pre trip inspection?

Why should drivers put the starter switch key in your pocket during the pre-trip inspection? To prevent the trailer from coming loose and rolling down an incline. To prevent electric shocks when checking the motor. To prevent injury from a running motor or other moving parts.

When you are inspecting hoses What should you look for?

With the engine off and cool, visually inspect belts and hoses. Gently tug them to confirm they are secure. If you see evidence of leaks, kinks, splits, cracks or abrasion, have a technician check it.

What is the most common problem found in roadside inspections?

• Inoperative required lamps. ...
• No or defective lighting. ...
• Inspection/repair and maintenance, parts and accessories. ...
• Tire tread depth less than 2/32 inch. ...
• Oil and/or grease leak.

What are the three types of emergency equipment?

What three kinds of emergency equipment must you have? Spare electrical fuses, three red reflective triangles, properly charged and rated fire extinguisher.