1. Try the plunger method. You know how powerful a plunger can be with your plumbing problems? ...
2. Use hot water for dented bumpers. Bumper plastic is hard for good reason. ...
3. Hammer out the dent. ...
4. Pop out the dent with a hair dryer and compressed air. ...
5. Buy a dent removal kit.

Can you fix car dents yourself?

Start off by heating the car dent with the hair dryer at its highest temperature, which will expand the plastic of the car. As soon as it's hot enough, grab the can of compressed air, turn it upside down, and begin spraying that same area. Since the cold air will cause the plastic to contract, the dent will pop out.

Do dent pullers really work?

Dent pullers only work on shallow dents on flat, flexible surfaces. They can improve the appearance of dents but probably won't create a perfect finish. But these tools will not work on deep, angular dents or damage along the edges of bodywork.

Do It Yourself Dent Repair bumper?

Use boiling water.

If the dent is on the plastic bumper (or another area of your car made of plastic), applying boiling water to the blemished area should take the dent right out. Boil a pot of water and pour it on the area with the dent, and then reach behind the bumper and push until the dent pops out.

Can you do paintless dent repair yourself?

If taking it to a body shop seems too time-consuming or expensive, paintless dent repair (PDR) kits offer a way of doing it yourself. These kits are especially useful if you have more than one blemish to smooth out.

Paintless Dent Removal DIY & PRO

How do you get a dent out of a car with hot water?

This can be accomplished by dousing the dent with hot water. Heat water to boiling in a pot or big tea kettle and pour it over the dent. Wearing gloves to protect your hands, quickly reach behind the bumper and push out the dent. If you can't get behind the bumper easily, remove it from the car for the procedure.

Will boiling water damage car paint?

The heat makes the metal more expandable and malleable, allowing it to be pushed and pulled easily. ... Pouring hot water over metal also has its problems. It could warp the metal out of shape, make it less sturdy; it could even ruin your paint job if your paint isn't up to par.

Does pouring hot water on a car dent work?

Make sure to keep on pouring the water until the plastic softens and you are able to bend the car dent back into place. ... Using boiling water on the car part is just as likely to cause further damage, which will only increase the cost of repair.

Do suction cups work on car dents?

If you don't have access to the back of the dent, you can remove dents with a small suction cup. ... The suction cup literally “sucks” the dent out of the metal and removes it from your car without drilling any holes.

What kind of dents can be popped out?

The dents which form a big depression on a body panel and not sharp indents can be pulled out. If there are cracks on the dented panel, the dent can most likely not be pulled out. Very large dents can not be suctioned out. If the body panel is made of aluminum, the dent cannot be pulled out in the majority of cases.

Does boiling water remove dents in metal?

Before applying tools, try the following: wash the dented surface with hot, possibly boiling water. With a bit of luck the metal will flex and pop back in its original form. ... The hot water always supplies sufficient heat to make the paint and the material smooth.

How do body shops fix dents?

To ensure that doesn't happen, body shops use a process called “paintless dent removal” (PDR). PDR requires no fillers or sanding, as a trained technician uses a variety of special tools to gently and slowly push dents back into place without harming the factory paint job.

How do you get minor dents out of your car?

The quickest and often easiest dent removal method is to use a sink or cup plunger, which will work on small to medium sized dents (depending on the plunger size). Wet the plunger and the dent, place the plunger over the damaged area and begin pushing and pulling.

How do you get a dent out of a car metal?

1. Using the heat gun/blow dryer, heat up the dent.
2. After it's warm to the touch, attach the suction dent puller.
3. Pull the dent out with the puller's handle.
4. Once you've reduced the dent's overall size, switch to the bridge puller.

How do you remove dents from metal?

Boiling Water: Simply pouring boiling water over your dents can be enough to pop them out in many cases. That's because the built-up stress in a dent is relieved when you apply heat and the metal or aluminum can relax enough to pop back out to its original shape.

How do you remove hailstorm dents?

Fortunately, hail dents can be easily popped back out again or repaired by a car dent repair specialist.
...
The quick change in temperature should cause the dent to pop out within a few minutes.

1. Lay a cold, wet cloth over the dent. ...
2. Spray compressed air over the dent. ...
3. Apply dry ice to the dent.

Can I pour boiling water on my car?

If you use boiling water on a very cold day, the glass could even shatter, leaving you with a very pricey repair bill – and all for the sake of a few minutes. Damaged paintwork – Pour scalding hot water on the windscreen, and you run the risk of damaging the paintwork as the water runs off.

Does a hair dryer remove dents?

The hair dryer dent removal method won't work on a car that's been totaled, but it generally works well on smaller dings and depressions in certain portions of your vehicle.

Can you fix a dented bumper with boiling water?

Yes, it can help remove dents from both metal and plastic bumpers. Fill a pot with water and bring it to a rolling boil. Carefully pour the water over the surface of the dent to heat up the metal. ... If the bumper is plastic, push the dent out from behind after you pour the hot water over it.

Can I hammer out a dent?

Hammering out the damage requires access to both sides of the dent: the underside and the outer surface. To get to the back of the dented metal, you need to remove door panels or fenders. You'll hammer against the dolly, as it stabilizes the taps made inside the dented surface from the outside of the sheet metal.